화이트앳-ATMEGA128,AVR 정복,아두이노,Cortex-M3

ST-LINK V2

ST-LINK V2는 STM32 STM8 등의 장치에 디버깅,라이팅 를 포함하여 양산이 가능합니다.

STM8 은 주로 Visual Programmer 를 사용하고
STM32 는 J-LINK 와 J-Flash 를 많이 사용합니다.

ST-LINK V2 저렴한 곳

키트128 쇼핑몰에서 저렴하게 구매할 수 있습니다.
http://kit128.com/goods/view?no=189

ST-LINK/V2

ST-Link V2는 ST Microelectronics의 STM8 and STM32 Microcontroller Families의 모든 제품에 사용 가능한 In-Circuit Debugger and Programmer 입니다. JTAG/SWD인터페이스를 이용해서 STM8 와 STM32에 프로그램 라이팅, 디버깅을 할 수 있습니다

특징

• 5 V power supplied by USB connector.
• USB 2.0 full speed interface compatible.
• USB standard A to Mini-B cable provided.
• SWIM specific features:
  • 1.65 V to 5.5 V application voltage supported on SWIM interface.
  • SWIM low speed and high speed modes supported.
  • SWIM programming speed rate:
    • 9.7 Kbytes/s in low speed,
    • 12.8 Kbytes/s in high speed.
  • SWIM cable for connection to an application with an ERNI standard connector vertical (ref: 284697 or 214017) or horizontal (ref: 214012).
  • SWIM cable for connection to an application with pin headers or 2.54 mm pitch connector.
• JTAG/serial wire debugging (SWD) specific features:
  • 1.65 V to 3.6 V application voltage supported on the JTAG/SWD interface and 5 V tolerant inputs.
  • JTAG cable for connection to a standard JTAG 20-pin pitch 2.54 mm connector
  • JTAG supported
  • SWD and serial wire viewer (SWV) communication supported
• Direct firmware update feature supported (DFU)
• Status LED which blinks during communication with the PC
• Operating temperature 0 to 50 °C
• 2500 VRMS high isolation voltage (ST-LINK/V2-ISOL only)

핀번호

드라이버

최신 ST-Link V2 드라이버는 화이트앳 ST-Link 드라이버 자료실(http://whiteat.com/index.php?mid=sw_pds&package_srl=228213) 에서 받으실수 있습니다.

사용예

ST-LINK V2 는 STM32 ST-LINK Utility ,  KEIL uVision 에서 사용할 수 있습니다.

연결

컴퓨의 USB에 USB 케이블을 연결하고 20핀 플랫케이블은 STM8 또는 STM32 보드에 연결합니다.

ST-LINK 에서는 보드에 전원을 공급해주지 않습니다. 필히 보드에 별도의 전원을 공급해줘야 합니다.

STM32 ST-LINK Utility 에서 사용

STM32 ST-LINK Utility 로 ST-LINK V2 를 사용하는 방법입니다.

http://docs.whiteat.com/?p=3048  

KEIL uVision에서 사용

KEIL uVision 로 ST-LINK V2 를 사용하는 방법입니다.

http://docs.whiteat.com/?p=3050

제품 구매

ST-LINK V2 제품은 http://kit128.com/goods/view?no=189 에서 구매하실 수 있습니다.

STM32F103CBT6

DATA SHEET:

STM32F103CBT6.pdf

Features

■ ARM 32-bit Cortex™-M3 CPU Core

– 72 MHz maximum frequency,

1.25 DMIPS/MHz (Dhrystone 2.1)

performance at 0 wait state memory access

– Single-cycle multiplication and hardware division

■ Memories

– 64 or 128 Kbytes of Flash memory

– 20 Kbytes of SRAM

■ Clock, reset and supply management

– 2.0 to 3.6 V application supply and I/Os

– POR, PDR, and programmable voltage detector (PVD)

– 4-to-16 MHz crystal oscillator

– Internal 8 MHz factory-trimmed RC

– Internal 40 kHz RC

– PLL for CPU clock

– 32 kHz oscillator for RTC with calibration

■ Low power

– Sleep, Stop and Standby modes

– VBAT supply for RTC and backup registers

■ 2 x 12-bit, 1 μs A/D converters (up to 16 channels)

– Conversion range: 0 to 3.6 V

– Dual-sample and hold capability

– Temperature sensor

■ DMA

– 7-channel DMA controller

– Peripherals supported: timers, ADC, SPIs, I2Cs and USARTs

■ Up to 80 fast I/O ports

– 26/37/51/80 I/Os, all mappable on 16

external interrupt vectors and almost all 5 V-tolerant

■ Debug mode

– Serial wire debug (SWD) & JTAG interfaces

■ 7 timers

– Three 16-bit timers, each with up to 4 IC/OC/PWM or pulse counter and

quadrature (incremental) encoder input

– 16-bit, motor control PWM timer with deadtime generation and emergency stop

– 2 watchdog timers (Independent and Window)

– SysTick timer 24-bit downcounter

■ Up to 9 communication interfaces

– Up to 2 x I2C interfaces (SMBus/PMBus)

– Up to 3 USARTs (ISO 7816 interface, LIN, IrDA capability, modem control)

– Up to 2 SPIs (18 Mbit/s)

– CAN interface (2.0B Active)

– USB 2.0 full-speed interface

■ CRC calculation unit, 96-bit unique ID

■ Packages are ECOPACK®

STM32F103C4T6A

DATA SHEET: 

CD00210843.pdf

Features

■ ARM 32-bit Cortex™-M3 CPU Core

– 72 MHz maximum frequency,

1.25 DMIPS/MHz (Dhrystone 2.1)

performance at 0 wait state memory

access

– Single-cycle multiplication and hardware

division

■ Memories

– 16 or 32 Kbytes of Flash memory

– 6 or 10 Kbytes of SRAM

■ Clock, reset and supply management

– 2.0 to 3.6 V application supply and I/Os

– POR, PDR, and programmable voltage

detector (PVD)

– 4-to-16 MHz crystal oscillator

– Internal 8 MHz factory-trimmed RC

– Internal 40 kHz RC

– PLL for CPU clock

– 32 kHz oscillator for RTC with calibration

■ Low power

– Sleep, Stop and Standby modes

– VBAT supply for RTC and backup registers

■ 2 x 12-bit, 1 μs A/D converters (up to 16

channels)

– Conversion range: 0 to 3.6 V

– Dual-sample and hold capability

– Temperature sensor

■ DMA

– 7-channel DMA controller

– Peripherals supported: timers, ADC, SPIs,

I2Cs and USARTs

■ Up to 51 fast I/O ports

– 26/37/51 I/Os, all mappable on 16 external

interrupt vectors and almost all 5 V-tolerant

Debug mode

– Serial wire debug (SWD) & JTAG interfaces

■ 6 timers

– Two 16-bit timers, each with up to 4

IC/OC/PWM or pulse counter and

quadrature (incremental) encoder input

– 16-bit, motor control PWM timer with deadtime

generation and emergency stop

– 2 watchdog timers (Independent and

Window)

– SysTick timer 24-bit downcounter

■ 6 communication interfaces

– 21 x I2C interface (SMBus/PMBus)

– 2 × USARTs (ISO 7816 interface, LIN, IrDA

capability, modem control)

– 1 × SPI (18 Mbit/s)

– CAN interface (2.0B Active)

– USB 2.0 full-speed interface

■ CRC calculation unit, 96-bit unique ID

■ Packages are ECOPACK®

STMicroelectronics STM8L-Discovery Board

■ On-board ST-LINK with selection mode switch to use the kit as stand-alone ST-LINK with SWD connector

■ Designed to be powered by USB or by external power 5V or 3.3V supply

■ Can supply target application with 5V or 3V

■ IDD consumption measurement in Low Power Modes

■ Two User LEDs (Green and Blue)

■ One User Push Button

■ Extension header for all I/Os for quick connection to prototyping board or easy probing

Quick, Cost-Effective Way to Discover STM8L MCUs

The STMicroelectronics STM8L-Discovery Board is based on the STM8L152C6T6 microcontroller (MCU) and is a quick-start evaluation board for STM8L ultra-low-power MCUs. The STM8L Discovery Board is the quickest way to discover the STM8L, to program and use the device, and to build and debug applications. This STMicroelectronics evaluation board includes the embedded debugger ST-LINK and an I_DD consumption measurement feature that helps you to discover the ultra-low-power efficiency. The STMicroelectronics STM8L-Discovery also features an LCD (24 segments, 4 commons), LEDs, and push buttons. Demonstration software is preloaded in the board's Flash memory, and numerous applications are available to learn, reuse, and modify code for a fast time to proof-of-concept or demonstration. The latest versions of this demonstration source code and associated documentation can be downloaded from www.st.com/stm8l-discovery. The STM8L-Discovery is ideal for hobbyists, developers, students, and support teams.

DATA BRIEF

APPLICATION NOTES

STM8S-discovery 키트

■ STM8S105C6T6 microcontroller, 32 KB Flash, 2 KB RAM, 1 KB EEPROM

■ Powered by USB cable between PC and STM8S-DISCOVERY

■ Selectable power of 5 V or 3.3 V

■ Touch sensing button

■ User LED

■ Extension header for all I/Os

■ Wrapping area for users own application

■ Embedded ST-Link

■ USB interface for programming and debugging

■ SWIM debug support

DATA BRIEF

APPLICATION NOTES

LICENSE AGREEMENTS

USER MANUALS